最近Flipper很火热，我也做个Flipper折刀的使用感受

真龙天子

刀轴调节一下试试，有5-10度的调整将很明显，并且不会出现摇头点头的间隙。
陈近南 发表于 2013-3-25 19:25

陈兄说的是HINDERER的XM-18吗？我试过把刀全拆了再装回去，由于不得要领，FLIPPER更紧.干脆以后都不弄了

ian

估计又是一个在米国的有米之人

花无期

陈兄说的是HINDERER的XM-18吗？我试过把刀全拆了再装回去，由于不得要领，FLIPPER更紧.干脆以后都不弄了
真龙天子 发表于 2013-3-25 19:57

我估计总舵主说的是我那支cobra的调试方法。XM-18还是等着HINDERER来调整吧。

陈近南

COBRA我没动过，因为拿到的时候就很完美。
我说的是XM-18，Rick没有在螺丝上封胶，可以拧的。至于拆了再装回去，好似记忆中在USN的Rick版块有一个教学贴。


----mmm，查了下，是一个教如何装的居中的帖子。没拆过，不敢说。。按我想么，只要垫片干净，装回去应该没啥吧。别拧的太死就行吧


Okay, I finally took my 3" XM-18 apart and cleaned it up. This knife has always been perfectly centered and the blade was really smooth and opened like lightning.

Usually when I put my XMs together and get the blade centered they are a little tight making it hard to flip open. When I got this one together, the blade was past center towards the lock face and still looser than I like.

I called Rob on the phone and he taught me a little trick that fixed the problem. I felt bad because while I was talking with Rob, my kids were going crazy in the back ground. He didn't seem to mind though.

Here we go:

1. Open blade to 90 degrees and tighten pivot so that it is really tight.

2. Close the blade and loosen frame screws so they aren’t tight, but still holding the frame together.

3. While the blade is still in the closed position, pull blade towards the side you want the blade to move. In my case, I pulled the blade toward the liner/scale.

4. While pulling blade, tighten the frame screws.

5. Loosen the pivot and adjust it to the desired tension.

These instructions helped to "reset" my blade. Now while in the centered position, my blade has a little more resistance. This is the way I like mine to be.

seallo

COBRA我没动过，因为拿到的时候就很完美。
我说的是XM-18，Rick没有在螺丝上封胶，可以拧的。至于拆了再装回去，好似记忆中在USN的Rick版块有一个教学贴。


----mmm，查了下，是一个教如何装的居中的帖子。没拆 ...
陈近南 发表于 2013-3-25 20:26

总舵主能否好人做到底，帮忙翻译下这个居中帖子的内容呢，对于我等英文烂的人来说看这种技术英文帖真是有难度呢，谢谢

陈近南

1. Open blade to 90 degrees and tighten pivot so that it is really tight.
打开到90度，拧紧主轴，拧到真的很紧

2. Close the blade and loosen frame screws so they aren’t tight, but still holding the frame together.
合上刀刃，松开主轴螺丝，但是别全拧开。

3. While the blade is still in the closed position, pull blade towards the side you want the blade to move. In my case, I pulled the blade toward the liner/scale.
此时刀片依然是合上的状态，把刀片扳向你希望他去的一边

4. While pulling blade, tighten the frame screws.
扳着刀片，拧主轴螺丝

5. Loosen the pivot and adjust it to the desired tension.
松开主轴，调整至需要的松紧

These instructions helped to "reset" my blade. Now while in the centered position, my blade has a little more resistance. This is the way I like mine to be.

真龙天子

看来有空我真的要按此法再试试

陈近南

我刚刚松了XM-18的螺丝，怎么地，也不能相当轻松的一拨就开，刀刃向下时，50%可以。
1、刀轴顺化程度自然是最重要的,XM-18顺滑程度比TODD BEGG差不多，比GALYEAN差，比PHIL，当然也不用说
2、定位珠的解开力道，18定位珠不够劲，以至于从定位珠里头出来时，力量不够。

抠的同时抖腕。一切都是浮云。

青纱帐

必须顶！学习了。

philon

好久没有看到江兄弟的帖子了。说的很中肯！我那个allen的flipper，自己调了几次，基本可以一次打开到位了，但合刀时稍有不居中。蛋疼的是，每次解除锁定时，都很费劲。指甲都被磨出了口子。。。

seallo

1. Open blade to 90 degrees and tighten pivot so that it is really tight.
打开到90度，拧紧主轴，拧到真的很紧

2. Close the blade and loosen frame screws so they aren’t tight, but still holding the ...
陈近南 发表于 2013-3-25 20:52

非常感谢！！就我个人的体会而言，xm-18初入手时确实没法flipper开刀，把主轴调整合适，并稍加练习后，几乎任意角度都可以比较轻松的flipper开刀。诀窍就是食指开刀时需要较大的爆发力。

totosu

一堆的宝贝

neobilly

卧虎藏龙！昨晚看前辈03年注册，才150多积分。今天直接技术分就加了200多。真是潜龙升天了

花无期

卧虎藏龙！昨晚看前辈03年注册，才150多积分。今天直接技术分就加了200多。真是潜龙升天了
neobilly 发表于 2013-3-25 23:55

“潜”字用得非常贴切，之前一直是个只看不回的潜水艇，经过了海底两万哩，也该出来透透气了。

xia36

都是好玩的好刀。

antonysea

作为教材收藏

ioio

姿势的海洋，感谢分享！

feng12345

品种多，漂亮的很

123ZKXX

看的我是一地口水啊

666

全是好刀